Home » DVR » Yamaha Soundbar Universal Remote Codes & Program Instructions

Yamaha Soundbar Universal Remote Codes & Program Instructions

If you want to control your yamaha sound bar using the universal remote or SAT or else with CAB remotes then you must use their codes which are specially designed for this yamaha sound bar.

Universal 5-digit remote control codes for Yamaha soundbar

  • 31947
  • 31331
  • 30176
  • 31176
  • 30354
  • 10030
  • 10797
  • 10017
  • 10019

Xfinity remote code for Yamaha soundbar

  • 992 (Note to use this code, follow the code search method mentioned below)

Using the remote control codes mentioned above, you can program the remote control with your yamaha sound bar. You can find the steps to program your remote to work with the soundbar. So check the steps below.

How to program the Yamaha Soundbar universal remote control?

Use the method below for the yamaha sound bar (codes 30176 or 31331)

(There must be a TV code programmed on the TV device or the volume keys will not work)

  • AV1 or AV2
  • Press and hold MUTE & SELECT button, you have to wait here for two flashes, then release it
  • Now enter 30176 then AV1 or AV2
  • Now hold down Mute & Select again, wait for two blinks, then release it
  • Now enter the code 993
  • Press Select
  • Then AV1 or AV2
  • Now press & hold Mute & Select then wait here for two blinks then release it
  • Enter now 963
  • Press CH Down
  • You must now enter the commands for the directv att remote control.

Or you can also use the method below….

Use code 30176 or 31331 for the Yamaha sound bar
(There must be a TV code programmed on the TV device or the volume keys will not work)
-AV1 or AV2
-Press and hold MUTE & SELECT until it gives 2 flashes
-Enter the code 993

In fact, the codes mentioned above can also be used to program yamaha sound bar models. The models are:

ATS-1030, YSP-1000, YSP-5100, YSP-4100, YSP-1400, YAS-101, YAS-103, YHT-S400 and YSP-4000BL

These codes have been tested with the following devices:

Comcast Remote Controls, Xfinity XR5, Device Remote Control DVR 3, Remote Control XR2, Xfinity XR2 U2, XR2 R2, DirecTV, Directv HR24 STB, S10-S4, U-verse Remote Control, RC65, H20 Satellite Receiver, DirecTV Plus HD DVR, Comcast 3-in-1 remote control and 1067BG3.

How to program the Yamaha Soundbar universal remote control without codes

In the automatic search method, all universal remote control codes have gone through a scanning process in the remote control. It scans one code at a time to find the correct remote code that works with your remote to program the command. Follow the instructions below:

How to program the Yamaha sound bar Universal remote control with manual method

Using the key code we can easily program a universal remote control and the key code identifies the make and model of your equipment.

  • You must first “Turn on the device”
  • press the “TV” On your “Yamaha Soundbar Universal Remote”
  • Now press and hold the “Configuration button” on the universal remote until it displays the “Bright flash” (This means it is in “learning mode”)
  • Finally enter the “Key code” that you have found in the programming guide (Instruction booklet)
  • Once you have done this procedure, all you need to do is “Point your remote control at the television” then “Press and hold the power” button
  • You can release the “Power button” every time the screen turns off

That’s it, your TV will work fine now with the universal remote control, if your device does not work then try repeating the same procedure with the different code from the same part of the reference table.

How to program the Yamaha soundbar universal remote control with Code search

If you can’t find the key code that works for the device at that time, you can configure your universal remote to search for the correct one. It’s a code in the manual that forces the remote into search mode

  • First of all “Turn on the device”
  • Now press and hold the “To install” button
  • Enter the “9-9-1” code (three digits)
  • Now hold the “Power button” on the remote control, then press the channel up until the device in this case your TV “Off”

The above method may take a little longer, but finding your key code is very important. Once you have completed the above procedure, your remote control should work for all in functions.

We hope the above methods and codes have been used to program your Yamaha Soundbar and also for your favorite remote control. These methods are used for setting up the Yamaha Soundbar remote control.

Now we will mention other methods to solve some problems. So check them once.

Photo of author

Suresh Choudhary

Suresh is a former writer for Lifewire who started reporting on consumer electronics in 2015. He's focused more closely on home entertainment and home theater technology like Ultra HD, Blu-ray, and DVD players. Since studying electronics in high school, he's been a fervent electronics and audiophile hobbyist.

Leave a Comment