Sanyo Soundbar Universal Remote Codes & Program Instructions

We have mentioned the three and five digit codes below, so check them one by one.

Sanyo Soundbar Universal Remote Codes

Sanyo Soundbar Universal 3-digit remote control

Sanyo Soundbar 4-digit universal remote control

0157
1156
1166

1176

Sanyo Soundbar 5-digit universal remote control

20047
10154

10159
10051
10250

20035
30189
30531

20081
21593
20593

20,000
20039
20149

21781

If you find that these remote codes do not work for your device, try following the code search on your CAB or SAT remote …

Must Read

Sanyo Soundbar Universal Remote Codes

How to turn on the Sanyo fwsb415e soundbar without a remote control

If you want to turn on your sanyo soundbar, there are two ways, one is to use the mobile app remote control and the other is to use universal remote like GE, RCA, Vizio, etc. sanyo fwsb415e and fwsb405fs soundbar models.

ATT RC7X remote control:

You can program the sanyo soundbar with the RC7X remote by doing the following:

Go to “Menu”
chose “Settings”

Then select “Settings and help”
Then “Remote control”
To select “Audio device” now

With DIRECTV or ATT as cable with the DIRECTV remote control:

Light up “Sanyo sound bar”
Click on “VOL +” corn “Muted”

chose “AV1” Where “AV2”
Keep up the pressure and hold “Mute” then “To select” until he gives “2 flashes”
Enter the “9 9 1” code and wait 2 flashes

Enter now “3”
Then press and release “VOL +”
Now place the remote in front of the sanyo soundbar, then keep pressing and releasing the “CH +” key

You may observe that your device changes the volume, at this time press “To select” it will therefore lock the code.

If the DIRECTV remote controls the power of the Sanyo soundbar but not the volume, try this:

To select “AV1 or AV2”

Then continue to press and hold the “Mute and select” buttons
Just wait until it turns out “Two flashes” then release
Now enter the code “9 9 3”

Finally press “To select”

Code search using a silver Comcast remote control with a red OK / Select button:

Light up “Sanyo sound bar”

Once click on “OF”
Now press and hold “To install” until you observe that the key flashes twice
Now release “To install”

Enter “9 9 1 3”
Now “OF” the key will flash twice
Then press “Power” after that, target your remote control on the sanyo sound bar

Now keep pressing “CH +” until the sound bar turns off
Important point: In this code search mode, the remote sends the IR code from its library to your selected device.
Then press “To install” so that the code is “Locked”

For confirmation, the aux key “Flashes twice”

With a Comcast Xfinity remote with the red ok button:

First press “OF” then press and hold “To install” until it blinks twice

Now “Enter the code” which we spoke about above.

With a Comcast Xfinity remote control with the red ok button – To lock the Sanyo sound bar:

Keep on hold “To install”Until it blinks twice

Now enter the code “9 9 3”
Then press “OF”

But to remove the padlock and then make it independent of each device:

Keep on hold “To install” until it blinks twice
Press the code “9 9 3” then press once “flight +”

(This is all you can choose for each device whose volume you would like to change)

How to program the Sanyo soundbar universal remote control without codes

In the automatic search method, all universal remote control codes have gone through a scanning process in the remote control. It scans one code at a time to find the correct remote code that works with your remote to program the command. Follow the instructions below:

“Light up” smart device like “TV” that you want the universal remote to work.
“Light up” remote control, press the button on the device (TV, DVD, CBL and OK / SEL) for 3 seconds. The LED indicator indicates that the device is ready to be programmed.

Point the remote control at the device and click “CH +” & “CH-“ switches. The remote will display the on / off signals. hurry “up” Where “down” continuously until the device switch off.
Check the code by clicking on “Power” key. The device must light up. If it starts, try changing the channel to verify that the remote is correctly programmed.
Now press the “device” button to save the code. The device LED will blink twice to confirm the stored code.

How to program the Sanyo sound bar Universal remote control with manual method

Using the key code we can easily program a universal remote control and the key code identifies the make and model of your equipment.

You must first “Turn on the device”
press the “TV” On your “Sanyo Soundbar universal remote control”

Now press and hold the “Configuration button” on the universal remote until it displays the “Bright flash” (This means it is in “learning mode”)
Finally enter the “Key code” that you have found in the programming guide (Instruction booklet)
Once you have done this procedure, all you need to do is “Point your remote control at the television” then “Press and hold the power” button

You can release the “Power button” every time the screen turns off

That’s it, your TV will work fine now with the universal remote control, if your device does not work then try repeating the same procedure with the different code from the same part of the reference table.

How to program the universal remote control of the Sanyo sound bar with Code search

If you can’t find the key code that works for the device at that time, you can configure your universal remote to search for the correct one. It’s a code in the manual that forces the remote into search mode

First of all “Turn on the device”
Now press and hold the “To install” button
Enter the “9-9-1” code (three digits)

Now hold the “Power button” on the remote control, then press the channel up until the device in this case your TV “Off”

The above method may take a little longer, but finding your key code is very important. Once you have completed the above procedure, your remote control should work for all in functions.