Home » Uncategorized » GE DVD Recorders + RW Universal Remote Codes

GE DVD Recorders + RW Universal Remote Codes

Controlling your GE + RW DVD burners is not possible until you have the functional codes. So here on this platform, you will have a full list of codes that work properly. It is not necessary to take the separate remote control for your devices. Other than that, the process that you need to go through is straightforward and easy. It is not necessary to acquire additional knowledge to program these codes and to ge codes for universal remote control look at this. Now you can entertain yourself with your favorite GE DVD Recorders + RW device.

List of universal remote control codes for GE + RW DVD recorders

CENTRIOS 0951, 1060, 1061
COBY 0894
GO-VIDEO 0431, 0902, 0901
HUMAX 0912
ILO 0959
JVC 0900, 1072
KXD 0894
LG 0907
LITEON 0902, 0898, 0959
MAGNAVOX [0979], [0980]
MEDION 0903, 0959
PHILIPPE [0979], [0980]
PHILIPS-MAGNAVOX [0979], [0980]
PIONEER 0977, 0909, 1084
RCA 0409
SANYO 0904
SHARP 0897
SONY 0987, 0988, 0989
TOSHIBA 0973, 0398
YAMAHA 0979, 0980

How to program the GE universal remote control without codes

In the automatic search method, all universal remote control codes have gone through a scanning process in the remote control. It scans one code at a time to find the correct remote code that works with your remote to program the command. Follow the instructions below:

  1. “Light up” smart device like “TV” that you want the universal remote to work.
  2. “Light up” remote control, press the button on the device (TV, DVD, CBL and OK / SEL) for 3 seconds. The LED indicator indicates that the device is ready to be programmed.
  3. Point the remote control at the device and click “CH +” & “CH-“ switches. The remote will display the on / off signals. hurry “up” Where “down” continuously until the device switch off.
  4. Check the code by clicking on “Power” key. The device must light up. If it starts, try changing the channel to verify that the remote is correctly programmed.
  5. Now press the “device” button to save the code. The device LED will blink twice to confirm the stored code.

How to program GE Universal remote control with manual method

Using the key code we can easily program a universal remote control and the key code identifies the make and model of your equipment.

  • You must first “Turn on the device”
  • press the “TV” On your “GE universal remote control”
  • Now press and hold the “Configuration button” on the universal remote until it displays the “Bright flash” (This means it is in “learning mode”)
  • Finally enter the “Key code” that you have found in the programming guide (Instruction booklet)
  • Once you have done this procedure, all you need to do is “Point your remote control at the television” then “Press and hold the power” button
  • You can release the “Power button” every time the screen turns off

That’s it, your TV will work fine now with the universal remote control, if your device does not work then try repeating the same procedure with the different code from the same part of the reference table.

How to program the GE universal remote control with Code search

If you can’t find the key code that works for the device at that time, you can configure your universal remote to search for the correct one. It’s a code in the manual that forces the remote into search mode

  • First of all “Turn on the device”
  • Now press and hold the “To install” button
  • Enter the “9-9-1” code (three digits)
  • Now hold the “Power button” on the remote control, then press the channel up until the device in this case your TV “Off”

The above method may take a little longer, but finding your key code is very important. Once you have completed the above procedure, your remote control should work for all in functions.

Well, now at the end of the article, hope you can easily use the universal remote control to successfully control your GE CABLE decoders. And, I’m sure there will be nothing you can’t do.

It was all about GE DVD Recorders + Universal RW Remote Control Codes and this is the time when you need to enjoy your TV shows and movies without having a headache. Now you can easily program your codes remotely just to control your different devices.

Photo of author

Suresh Choudhary

Suresh is a former writer for Lifewire who started reporting on consumer electronics in 2015. He's focused more closely on home entertainment and home theater technology like Ultra HD, Blu-ray, and DVD players. Since studying electronics in high school, he's been a fervent electronics and audiophile hobbyist.

Leave a Comment