Have you brought a universal remote recently? don’t you know the remote control codes for the Dynex TV. In this article, we are going to provide all kinds of universal remote control codes for Dynex TV such as three and four digit codes etc. which you can get below.
- 1 Dynex Universal Remote Control Code List
- 2 How to program the Dynex universal remote with automatic search
- 3 How to program Dynex Universal remote control with manual method
- 4 How to program the Dynex universal remote with Code search
Dynex Universal Remote Control Code List
|Comcast M1057||0463, 10463, 096|
|RC23 Direct TV||10463|
|Dish Network VIP508||720|
|Dish Network VIP622||720|
|One for all URC-6690||0464|
|TiVo SERIES 3||091|
Try these codes first
Dynex 4-digit universal remote control codes
2049, 2184, 1463, 5311, 3141, 3161, 0371, 2891, 1040, 1181, 1171, 0135, 1718, 0115, 5421
Dynex 5-digit universal remote control codes
10180, 10178, 10171, 10623, 11963, 10096, 10463, 10154, 10236, 10463, 12049, 12184, 11463, 11780, 11785, 11810, 12288, 11631, 13700, 18924, 13153, 11435
Dynex Universal 3-Digit Remote Control Codes
720, 001, 538, 533, 834, 632, 256, 583, 585, 701, 706, 698, 726, 500, 220, 908, 587, 333, 603, 221, 115, 503, 666, 800, 120, 650, 844, 724, 200
GE Universal Remote Control Codes for Dynex TV
3141, 5311, 3161, 6521, 0371, 2891
Universal RCA Remote Control Codes for Dynex TV
Philips Dynex universal remote control codes
How to program the Dynex universal remote with automatic search
In the automatic search method, all universal remote control codes have gone through a scanning process in the remote control. It scans one code at a time to find the correct remote code that works with your remote to program the command. Follow the instructions below:
Using the key code we can easily program a universal remote control and the key code identifies the make and model of your equipment.
- You must first “Turn on the device”
- press the “TV” On your “Dynex Universal Remote”
- Now press and hold the “Configuration button” on the universal remote until it displays the “Bright flash” (This means it is in “learning mode”)
- Finally enter the “Key code” that you have found in the programming guide (Instruction booklet)
- Once you have done this procedure, all you need to do is “Point your remote control at the television” then “Press and hold the power” button
- You can release the “Power button” every time the screen turns off
That’s it, your TV will work fine now with the universal remote control, if your device does not work then try repeating the same procedure with the different code from the same part of the reference table.
How to program the Dynex universal remote with Code search
If you can’t find the key code that works for the device at that time, you can configure your universal remote to search for the correct one. It’s a code in the manual that forces the remote into search mode
- First of all “Turn on the device”
- Now press and hold the “To install” button
- Enter the “9-9-1” code (three digits)
- Now hold the “Power button” on the remote control, then press the channel up until the device in this case your TV “Off”
The above method may take a little longer, but finding your key code is very important. Once you have completed the above procedure, your remote control should work for all in functions. With the above three methods, we can easily program our Dynex TV Device universal remote control.
The list mentioned above is for universal remote control codes that are useful to the Dynex TV. If you find that any of these codes cannot work on your remote, you should try the next code which is mentioned in the list.
If you have additional codes that are not mentioned in the list above, leave that code in the comments section below.